too cheap to fix?

Relax in southern comfort on the east bank of the Mississippi. You're just around the corner from Beale Street and Sun Records. Watch the ducks, throw back a few and tell us what's on your mind.
billshurv
Posts: 424
Joined: Thu Feb 01, 2018 7:07 am

Re: too cheap to fix?

Post by billshurv » Sun May 31, 2020 5:47 pm

Well I did a fibreglass repair on a kiddy slide today. You can't buy the plastic parts seperate from the whole thing and I suspect compared to the last slide I had from the same company 20 years ago they've cost reduced the moulding to break after a few years! For my first ever fibreglassing it actually worked....so far. If it holds a year I will be very happy.

User avatar
JR.
Posts: 3324
Joined: Sat May 24, 2008 7:21 pm
Contact:

Re: too cheap to fix?

Post by JR. » Wed Jun 03, 2020 12:10 pm

I really hated working with fiberglass... My summer vacation job as a teen in high school was working in a machine shop and as a "young" man, I generally got the bottom of the barrel crap jobs. One of those jobs was making water barrel hoods (actually scoops) to channel sea water into the water barrels for oceanographic research.

The part of working with fiberglass that really sucked IMO, was sanding it to smooth rough edges/surfaces. Working in the summer heat, the fine fiberglass powder stuck to sweaty skin, and got into everything. :lol:

JR
Don't only half-ass tune your drums. Visit https://circularscience.com to hear what properly "cleared" drums sound like.

User avatar
JR.
Posts: 3324
Joined: Sat May 24, 2008 7:21 pm
Contact:

Re: too cheap to fix?

Post by JR. » Sun Jun 14, 2020 11:03 am

I finally got a letter back from Walmart answering my written complaint about the cheap lamp design... they passed the buck to some California company, gave me their phone number. Of course I'n mot going to call them.

JR
Don't only half-ass tune your drums. Visit https://circularscience.com to hear what properly "cleared" drums sound like.

User avatar
mediatechnology
Posts: 4321
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: too cheap to fix?

Post by mediatechnology » Sun Jun 14, 2020 1:54 pm

JR. wrote:
Sun Jun 14, 2020 11:03 am
I finally got a letter back from Walmart answering my written complaint about the cheap lamp design... they passed the buck to some California company, gave me their phone number. Of course I'n mot going to call them.

JR
Who would then refer you to China... :lol:
https://ka-electronics.com

"States Ordered To Fraudulently Inflate COVID-19 Cases 15 Times Actual Rate"
https://banned.video/watch?id=5efab695672706002f367a0a
"Plandemic/Doctors In Black" https://proaudiodesignforum.com/content/Plandemic.mp4

User avatar
JR.
Posts: 3324
Joined: Sat May 24, 2008 7:21 pm
Contact:

Re: too cheap to fix?

Post by JR. » Sun Jun 14, 2020 7:03 pm

mediatechnology wrote:
Sun Jun 14, 2020 1:54 pm
JR. wrote:
Sun Jun 14, 2020 11:03 am
I finally got a letter back from Walmart answering my written complaint about the cheap lamp design... they passed the buck to some California company, gave me their phone number. Of course I'n mot going to call them.

JR
Who would then refer you to China... :lol:
The company they bumped me too doesn't even make lamps. This was probably some knock off of a domestic design, that they screwed up making it cheaper. My complaint is with a) crappy design (threaded soft aluminum tubing), b) broken-missing part that wasn't still in the box so broken before shipping, c) "and" shipping damage where that broken part was still inside the shipping box.

I was expecting somebody in AR to take a little responsibility for the sleazy design practice, but not even. :roll:

I sold my Walmart stock years ago, but sadly they are kicking ass, and getting more of my purchases these days. FWIW I fixed and am using both lamps right now. Still a value.

JR
Don't only half-ass tune your drums. Visit https://circularscience.com to hear what properly "cleared" drums sound like.

Post Reply